收藏本站
MBCM270F450M270A00 - MBCM270T450M270A00
10.0 INPUT AND OUTPUT FILTER DESIGN
A major advantage of SAC TM systems versus conventional PWM
converters is that the transformers do not require large
functional filters. The resonant LC tank, operated at extreme
high frequency, is amplitude modulated as a function of input
voltage and output current and efficiently transfers charge
through the isolation transformer. A small amount of
capacitance embedded in the input and output stages of the
storage may be more densely and efficiently provided by
adding capacitance at the input of the module. At frequencies
<500 kHz the module appears as an impedance of R OUT
between the source and load.
Within this frequency range, capacitance at the input appears
as effective capacitance on the output per the relationship
defined in Eq. 5.
module is sufficient for full functionality and is key to achieve
power density.
This paradigm shift requires system design to carefully evaluate
C OUT =
C IN
K 2
Eq. 6
external filters in order to:
This enables a reduction in the size and number of capacitors
1. Guarantee low source impedance:
To take full advantage of the BCM TM module’s dynamic
response, the impedance presented to its input terminals
must be low from DC to approximately 5 MHz. The
connection of the bus converter module to its power
source should be implemented with minimal distribution
inductance. If the interconnect inductance exceeds
100 nH, the input should be bypassed with a RC damper
to retain low source impedance and stable operation. With
an interconnect inductance of 200 nH, the RC damper
may be as high as 1 μF in series with 0.3 Ω . A single
electrolytic or equivalent low-Q capacitor may be used in
place of the series RC bypass.
2. Further reduce input and/or output voltage ripple without
sacrificing dynamic response:
Given the wide bandwidth of the module, the source
response is generally the limiting factor in the overall
system response. Anomalies in the response of the source
will appear at the output of the module multiplied by its
K factor. This is illustrated in Figures 13 and 14.
used in a typical system.
11.0 THERMAL CONSIDERATIONS
V ? I Chip TM products are multi-chip modules whose temperature
distribution varies greatly for each part number as well as
with the input / output conditions, thermal management and
environmental conditions. Maintaining the top of the
MBCM270F450M270A00 case to less than 100oC will keep all
junctions within the V ? I Chip module below 125oC for most
applications.
The percent of total heat dissipated through the top surface
versus through the J-lead is entirely dependent on the
particular mechanical and thermal environment. The heat
dissipated through the top surface is typically 60%. The heat
dissipated through the J-lead onto the PCB surface is typically
40%. Use 100% top surface dissipation when designing for a
conservative cooling solution.
It is not recommended to use a V ? I Chip module for an
extended period of time at full load without proper
heat sinking.
3. Protect the module from overvoltage transients imposed
by the system that would exceed maximum ratings and
cause failures:
The module input/output voltage ranges shall not be
exceeded. An internal overvoltage lockout function
prevents operation outside of the normal operating input
range. Even during this condition, the powertrain is exposed
to the applied voltage and power MOSFETs must withstand
it. A criterion for protection is the maximum amount of
energy that the input or output switches can tolerate if
avalanched.
Total load capacitance at the output of the BCM module shall
not exceed the specified maximum. Owing to the wide
bandwidth and low output impedance of the module,
low-frequency bypass capacitance and significant energy
Rev. 1.1
V?I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200
1/2011
Page 14 of 19
v i c o r p o w e r. c o m
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MC22FF102D-F CAP MICA 1000PF 1KV 0.5% 2220
MCM01-031EC152J-F CAP MICA 1500PF 300V 5% SMD
MEA1D4805SC CONV DC/DC 1KVDC 1W 48 +-5V TH
MEE3S0512SC DC/DC CONVERTER 12V 3W ISOLATED
MER1S1515SC CONV DC/DC 1KVDC TH 1W 15-15V
MEV1D2412DC DC/DC 3KVDC DIP 1W 24V TO +/-12V
MEV3S0509SC CONV DC/DC 3W 5V IN 9V OUT SIP
MEXY2A562K CAP FILM 5600PF 275VAC RADIAL
相关代理商/技术参数
MBCN 功能描述:ACCY MOBILE-BASE CONV VHF/UHF N RoHS:是 类别:RF/IF 和 RFID >> RF配件 系列:* 标准包装:1 系列:*
MBCNMO 功能描述:ACCY MISC MBC RoHS:是 类别:RF/IF 和 RFID >> RF配件 系列:* 标准包装:1 系列:*
MBCON-3-1-0 功能描述:PCB CONN RA MALE TYPE A 3PIN SMC 制造商:power integrations 系列:- 零件状态:在售 配件类型:连接器 配套使用产品/相关产品:ISO5125I 系列 标准包装:1
MBCON-3-2-0 功能描述:PCB CONN VERT MALE TYPE P 3PIN S 制造商:power integrations 系列:- 零件状态:在售 配件类型:连接器 配套使用产品/相关产品:ISO5125I 系列 标准包装:1
MBCON-4-1-0 功能描述:PCB CONN RA MALE TYPE A 4PIN SMC 制造商:power integrations 系列:- 零件状态:在售 配件类型:连接器 配套使用产品/相关产品:ISO5125I 系列 标准包装:1
MBCON-4-2-0 功能描述:PCB CONN VERT MALE TYPE P 4PIN S 制造商:power integrations 系列:- 零件状态:在售 配件类型:连接器 配套使用产品/相关产品:ISO5125I 系列 标准包装:1
MBCOVC10 制造商:Eaton Corporation 功能描述:REPLACEMENT COVER FOR BR1020B100GK AND BR1020B100PK LOADCTR
MBCOVC15 制造商:Eaton Corporation 功能描述:REPLACEMENT COVER FOR BR1632B200GK AND BR1632B200PK LOADCTR